Encore Forums Encore Forums

Knowledgebase  Register  Login  My Profile  Inbox  Address Book  My Subscription  My Forums 

Photo Gallery  Member List  Search  Calendars  FAQ  Ticket List  Log Out

shadows on photos

  		Logged in as: Guest
  Printable Version
All Forums >> [Product Forums] >> [Productivity Software] >> PrintMaster 5.0 (released 2012) >> shadows on photos Page: [1]
Login
Message << Older Topic   Newer Topic >>
shadows on photos - 3/18/2014 8:23:07 AM   
o.ray@mwt.net

 

Posts: 3
Joined: 3/17/2014
Status: offline 		hi ! I'm having trouble with shadows showing up on items that are scanned onto a poster. items that I have scanned in with my printer and stored in my photo file. when I scan and print from my printer it prints just fine. when I have scanned a full size 8.5 x 11 it comes out smaller on the poster and I get warnings about pixilating if I enlarge it. also when I have a title box which is lined up with headers on the left --the print jumps around and off register when I go to print. thanks!! ray
Post #: 1
RE: shadows on photos - 3/18/2014 10:34:59 AM   
ellengard


Posts: 3253
Joined: 10/2/2006
Status: offline
quote:

ORIGINAL: o.ray@mwt.net
... when I have scanned a full size 8.5 x 11 it comes out smaller on the poster and I get warnings about pixilating if I enlarge it.

Scan at a resolution of 300 dpi of higher. The resulting file size is very large (several MB), but necessary for high quality printing.

quote:

... when I have a title box which is lined up with headers on the left --the print jumps around and off register when I go to print.

Someone else mentioned a problem with text printing. I'll find out if it's a problem in the program and get back to you.

(in reply to o.ray@mwt.net)
Post #: 2
RE: shadows on photos - 3/18/2014 5:50:01 PM   
ellengard


Posts: 3253
Joined: 10/2/2006
Status: offline
quote:

ORIGINAL: o.ray@mwt.net
--the print jumps around and off register when I go to print.

I found this tech note which may address your problem:
http://support.encore.com/technicalsupport/kb.aspx?kb_id=1533&product_id=2816

If that does not help, you can submit a tech support ticket here:
http://support.encore.com/technicalsupport/tech_support_frm.aspx?product_id=2816
(version 5.0 doesn't have its own category, but should be covered under version 2012)

Please post back if none of the above helps.

(in reply to o.ray@mwt.net)
Post #: 3
RE: shadows on photos - 3/19/2014 5:20:04 PM   
o.ray@mwt.net

 

Posts: 3
Joined: 3/17/2014
Status: offline 		I WENT TO OFFICE DEPOT TODAY WHERE I BOUGHT THE HP 5510 PHOTOSMART PRINTER/SCANNER. THEY SAY ITS THE SCANNER THKA'S NOT ADJUSTED PROPERLY. I OPENED EVERY THING I COULD FIND AND THERE'S NO SETTING FOR THE AREA TO BE SCANNED THAT I CAN FIND. APPARENTLY THESE THINGS ARE THROW AWAY THESE DAYS. I MAY HAVE TO BUY A DIFFERENT ONE. I'LL LOOK FOR HP TECH HELP FIRST. THANKS FOR THE HELP!!

(in reply to o.ray@mwt.net)
Post #: 4
RE: shadows on photos - 3/19/2014 5:54:30 PM   
ellengard


Posts: 3253
Joined: 10/2/2006
Status: offline 		Did you get a disk with your scanner? The scanning program should be on it. When you install and run the scanning program, there will be scanning options letting you chose the resolution, type of scan (e.g. photo, text, magazine, etc.) and a preview pane so you can crop to the area you want scanned, rather than scanning the entire platen.

(in reply to o.ray@mwt.net)
Post #: 5
RE: shadows on photos - 3/19/2014 7:32:04 PM   
o.ray@mwt.net

 

Posts: 3
Joined: 3/17/2014
Status: offline 		I FINALLY FOUND IT------I'LL HAVE TO WORK ON IT TOMORROW THANKS!!

(in reply to o.ray@mwt.net)
Post #: 6
Page:   [1]
All Forums >> [Product Forums] >> [Productivity Software] >> PrintMaster 5.0 (released 2012) >> shadows on photos Page: [1]
Jump to:





New Messages No New Messages
Hot Topic w/ New Messages Hot Topic w/o New Messages
Locked w/ New Messages Locked w/o New Messages
 Post New Thread
 Reply to Message
 Post New Poll
 Submit Vote
 Delete My Own Post
 Delete My Own Thread
 Rate Posts


Please Note: In order to post a message on the forums, you will need to become an Encore Forum Member. Click on the Register link on the top of this page and follow the instructions to become an Encore Forum Member.

If you are a new member and need help using these forums, please click on the FAQ link at the top of this page.

Forum Software © ASPPlayground.NET Advanced Edition 2.4

0.031